中文 ENGLISH
Your position : Home  > Products > Evaporation equipment

Falling film evaporator

Single-effect falling film evaporator

System composition:

Evaporator、separator、condenser、thermal compression pump、vacuum pump、liquid transfer pump、 platform、electrical instrument control cabinet, level automatic control system and valve&pipe fittings, etc.


Products features:

1.Because of the whole equipment uniform heating steam heating system, material liquid to liquid film flow evaporation, so it has high heat transfer efficiency, short heating time ,etc major features. If relocation thermal compression pump, more energy saving, low steam consumption and low cooling water circulation.
  2.The material flow accelerated down the tube wall pressure evaporation, adapt to the larger material liquid viscosity evaporation concentration.
  3.Because the material in each tube formed into membrane evaporation and material liquid heating time is very short, so evaporation and concentration is very good, especially for food larger preserve the nutrition of the food.
  4.Under vacuum evaporation process, not only ensure the material requirement, also ensure the requirements of environmental protection, at the same time, greatly reduces the evaporation temperature, plus configuration thermal compression pump, part of the secondary steam by thermal compression pump suction again and raw mix, saves the steam, at the same time by thermal compression pump heating steam spray fog shaped into the shell, steam quickly spread, material liquid heating slowly, so the suitable concentration of thermal sensitive material.
  5.Equipment is suitable for evaporation and concentration of foam materials , due to the material liquid into membrane evaporation in the heating tube, which form the gas-liquid separation,at the same time, most of the material liquid at the bottom of the body is siphoned off, only a small part of the material liquid into separator separation, the whole process of material liquid forming no too big impact, greatly reduce the formation of bubbles.
  6.For food, evaporating equipment can have sterilization function at the same time, the material after preheating first, and then into the sterilizer, reach more than 94 degrees, hold on 24 seconds, which entered 1st -effect , rapid flash of material, temperature in an instant.
  7.Equipment equip with CIP clean system, realize the in-place cleaning,  the whole set of equipment is easy to operate, no dead Angle.
  8.Design continuous feeding and discharging.
  9.Equipment can equip with automation system, can be configured to realize automatic feed rate control, the heating temperature automatic control, automatic discharging concentration control, automatic cleaning control, can also be equipped with a sudden power failure, failure protection for sensitive material. Other safety, alarm and other automation control.


Range of application:

Suitable for evaporation concentration is lower than the saturation density of salt material, and heat sensitive, viscosity, foaming, concentration is low, liquidity good sauce class material. Especially suitable for milk, glucose, starch, xylose, pharmaceutical, chemical and biological engineering, environmental engineering, waste liquid recycling etc for evaporation and concentration, low temperature continuous has high heat transfer efficiency, shorter time for heating the material, etc main features.
Evaporation capacity: 100-2000Kg/h (Series)
In consideration of each factories all kinds of solutions with different characteristics and complexity, our company will provide specific technical scheme according to client’s requirements, reference for users to choose!

 

Project

Single-effect

Double-effect

Triple-effect

Four-effect

Five-effect

Water evaporationcapacity (kg/h)

100-2000

500-4000

1000-5000

8000-40000

10000-60000

Steam pressure

0.5-0.8Mpa

Steamconsumption/evaporation capacity (With thermal compression pump)

0.65

0.38

0.28

0.23

0.19

Steam pressure

0.1-0.4Mpa

Steamconsumption/evaporation capacity

1.1

0.57

0.39

0.29

0.23

Evaporationtemperature (℃)

45-95℃

Cooling waterconsumption/evaporation capacity

28

11

8

7

6

Remark: In additionto the specifications in the table, can be separately designed according tocustomer's specific material.

Double-effect falling film evaporator

双效降膜蒸发器.jpg

System composition:

Evaporator、separator、condenser、thermal compression pump、vacuum pump、liquid transfer pump、 platform、electrical instrument control cabinet, level automatic control system and valve&pipe fittings, etc.


Products features:

1.Because of the whole equipment uniform heating steam heating system,  material liquid to liquid film flow evaporation, so it has high heat transfer  efficiency, short heating time ,etc major features. If relocation thermal  compression pump, more energy saving, low steam consumption and low cooling  water circulation.
 2.The material flow accelerated down the tube wall pressure evaporation,  adapt to the larger material liquid viscosity evaporation concentration.
 3.Because the material in each tube formed into membrane evaporation and  material liquid heating time is very short, so evaporation and concentration is  very good, especially for food larger preserve the nutrition of the food.
 4.Under vacuum evaporation process, not only ensure the material  requirement, also ensure the requirements of environmental protection, at the  same time, greatly reduces the evaporation temperature, plus configuration  thermal compression pump, part of the secondary steam by thermal compression  pump suction again and raw mix, saves the steam, at the same time by thermal  compression pump heating steam spray fog shaped into the shell, steam quickly  spread, material liquid heating slowly, so the suitable concentration of  thermal sensitive material.
 5.Equipment is suitable for evaporation and concentration of foam materials  , due to the material liquid into membrane evaporation in the heating tube,  which form the gas-liquid separation,at the same time, most of the material  liquid at the bottom of the body is siphoned off, only a small part of the  material liquid into separator separation, the whole process of material liquid  forming no too big impact, greatly reduce the formation of bubbles.
 6.For food, evaporating equipment can have sterilization function at the  same time, the material after preheating first, and then into the sterilizer,  reach more than 94 degrees, hold on 24 seconds, which entered 1st  -effect , rapid flash of material, temperature in an instant.
 7.Equipment equip with CIP clean system, realize the in-place  cleaning,  the whole set of equipment is  easy to operate, no dead Angle.
 8.Design continuous feeding and discharging.
 9.Equipment can equip with automation system, can be configured to realize  automatic feed rate control, the heating temperature automatic control,  automatic discharging concentration control, automatic cleaning control, can  also be equipped with a sudden power failure, failure protection for sensitive  material. Other safety, alarm and other automation control.


Range of application:

Suitable for evaporation concentration is lower than the saturation density of salt material, and heat sensitive, viscosity, foaming, concentration is low, liquidity good sauce class material. Especially suitable for milk, glucose, starch, xylose, pharmaceutical, chemical and biological engineering, environmental engineering, waste liquid recycling etc for evaporation and concentration, low temperature continuous has high heat transfer efficiency, shorter time for heating the material, etc main features.
Evaporation capacity: 1000-60000kg/h (Series)
In consideration of each factories all kinds of solutions with different characteristics and complexity, our company will provide specific technical scheme according to client’s requirements, reference for users to choose!


Project

Single-effect

Double-effect

Triple-effect

Four-effect

Five-effect

Water evaporationcapacity (kg/h)

100-2000

500-4000

1000-5000

8000-40000

10000-60000

Steam pressure

0.5-0.8Mpa

Steamconsumption/evaporation capacity (With thermal compression pump)

0.65

0.38

0.28

0.23

0.19

Steam pressure

0.1-0.4Mpa

Steamconsumption/evaporation capacity

1.1

0.57

0.39

0.29

0.23

Evaporationtemperature (℃)

45-95℃

Cooling waterconsumption/evaporation capacity

28

11

8

7

6

Remark: In additionto the specifications in the table, can be separately designed according tocustomer's specific material.

Triple-effect falling film evaporator

6.3T牛奶三效蒸发器2(还没保温).jpg

System composition:

Evaporator、separator、condenser、thermal compression pump、vacuum pump、liquid transfer pump、 platform、electrical instrument control cabinet, level automatic control system and valve&pipe fittings, etc.


Products features:

1.Because of the whole equipment uniform heating steam heating system,  material liquid to liquid film flow evaporation, so it has high heat transfer  efficiency, short heating time ,etc major features. If relocation thermal  compression pump, more energy saving, low steam consumption and low cooling  water circulation.<br>
2.The material flow accelerated down the tube wall pressure evaporation,  adapt to the larger material liquid viscosity evaporation concentration.<br>
3.Because the material in each tube formed into membrane evaporation and  material liquid heating time is very short, so evaporation and concentration is  very good, especially for food larger preserve the nutrition of the food. <br>
4.Under vacuum evaporation process, not only ensure the material  requirement, also ensure the requirements of environmental protection, at the  same time, greatly reduces the evaporation temperature, plus configuration  thermal compression pump, part of the secondary steam by thermal compression  pump suction again and raw mix, saves the steam, at the same time by thermal  compression pump heating steam spray fog shaped into the shell, steam quickly  spread, material liquid heating slowly, so the suitable concentration of  thermal sensitive material.<br>
5.Equipment is suitable for evaporation and concentration of foam materials  , due to the material liquid into membrane evaporation in the heating tube,  which form the gas-liquid separation,at the same time, most of the material  liquid at the bottom of the body is siphoned off, only a small part of the  material liquid into separator separation, the whole process of material liquid  forming no too big impact, greatly reduce the formation of bubbles.<br>
6.For food, evaporating equipment can have sterilization function at the  same time, the material after preheating first, and then into the sterilizer,  reach more than 94 degrees, hold on 24 seconds, which entered 1st  -effect , rapid flash of material, temperature in an instant.<br>
7.Equipment equip with CIP clean system, realize the in-place  cleaning,  the whole set of equipment is  easy to operate, no dead Angle.<br>
8.Design continuous feeding and discharging.<br>
9.Equipment can equip with automation system, can be configured to realize  automatic feed rate control, the heating temperature automatic control,  automatic discharging concentration control, automatic cleaning control, can  also be equipped with a sudden power failure, failure protection for sensitive  material. Other safety, alarm and other automation control.


 Range of application:

Suitable for evaporation concentration is lower than the saturation density of salt material, and heat sensitive, viscosity, foaming, concentration is low, liquidity good sauce class material. Especially suitable for milk, glucose, starch, xylose, pharmaceutical, chemical and biological engineering, environmental engineering, waste liquid recycling etc for evaporation and concentration, low temperature continuous has high heat transfer efficiency, shorter time for heating the material, etc main features.
Evaporation capacity: 1000-60000kg/h(Series)
In consideration of each factories all kinds of solutions with different characteristics and complexity, our company will provide specific technical scheme according to client’s requirements, reference for users to choose!

 

Project

Single-effect

Double-effect

Triple-effect

Four-effect

Five-effect

Water evaporationcapacity (kg/h)

100-2000

500-4000

1000-5000

8000-40000

10000-60000

Steam pressure

0.5-0.8Mpa

Steamconsumption/evaporation capacity (With thermal compression pump)

0.65

0.38

0.28

0.23

0.19

Steam pressure

0.1-0.4Mpa

Steamconsumption/evaporation capacity

1.1

0.57

0.39

0.29

0.23

Evaporationtemperature (℃)

45-95℃

Cooling waterconsumption/evaporation capacity

28

11

8

7

6

Remark: In additionto the specifications in the table, can be separately designed according tocustomer's specific material.

Four effect falling film evaporator

2014081815020811398.jpg

System composition:

Evaporator、separator、condenser、thermal compression pump、vacuum pump、liquid transfer pump、 platform、electrical instrument control cabinet, level automatic control system and valve&pipe fittings, etc.


Products features:

1.Because of the whole equipment uniform heating steam heating system, material liquid to liquid film flow evaporation, so it has high heat transfer efficiency, short heating time ,etc major features. If relocation thermal compression pump, more energy saving, low steam consumption and low cooling water circulation.
2.The material flow accelerated down the tube wall pressure evaporation, adapt to the larger material liquid viscosity evaporation concentration.
3.Because the material in each tube formed into membrane evaporation and material liquid heating time is very short, so evaporation and concentration is very good, especially for food larger preserve the nutrition of the food.
4.Under vacuum evaporation process, not only ensure the material requirement, also ensure the requirements of environmental protection, at the same time, greatly reduces the evaporation temperature, plus configuration thermal compression pump, part of the secondary steam by thermal compression pump suction again and raw mix, saves the steam, at the same time by thermal compression pump heating steam spray fog shaped into the shell, steam quickly spread, material liquid heating slowly, so the suitable concentration of thermal sensitive material.
5.Equipment is suitable for evaporation and concentration of foam materials , due to the material liquid into membrane evaporation in the heating tube, which form the gas-liquid separation,at the same time, most of the material liquid at the bottom of the body is siphoned off, only a small part of the material liquid into separator separation, the whole process of material liquid forming no too big impact, greatly reduce the formation of bubbles.
6.For food, evaporating equipment can have sterilization function at the same time, the material after preheating first, and then into the sterilizer, reach more than 94 degrees, hold on 24 seconds, which entered 1st -effect , rapid flash of material, temperature in an instant.
7.Equipment equip with CIP clean system, realize the in-place cleaning,  the whole set of equipment is easy to operate, no dead Angle.
8.Design continuous feeding and discharging.
9.Equipment can equip with automation system, can be configured to realize automatic feed rate control, the heating temperature automatic control, automatic discharging concentration control, automatic cleaning control, can also be equipped with a sudden power failure, failure protection for sensitive material. Other safety, alarm and other automation control.


 Range of application:

Suitable for evaporation concentration is lower than the saturation density of salt material, and heat sensitive, viscosity, foaming, concentration is low, liquidity good sauce class material. Especially suitable for milk, glucose, starch, xylose, pharmaceutical, chemical and biological engineering, environmental engineering, waste liquid recycling etc for evaporation and concentration, low temperature continuous has high heat transfer efficiency, shorter time for heating the material, etc main features.
Evaporation capacity: 1000-60000Kg/h (Series)
In consideration of each factories all kinds of solutions with different characteristics and complexity, our company will provide specific technical scheme according to client’s requirements, reference for users to choose!


Project

Single-effect

Double-effect

Triple-effect

Four-effect

Five-effect

Water evaporationcapacity (kg/h)

100-2000

500-4000

1000-5000

8000-40000

10000-60000

Steam pressure

0.5-0.8Mpa

Steamconsumption/evaporation capacity (With thermal compression pump)

0.65

0.38

0.28

0.23

0.19

Steam pressure

0.1-0.4Mpa

Steamconsumption/evaporation capacity

1.1

0.57

0.39

0.29

0.23

Evaporationtemperature (℃)

45-95℃

Cooling waterconsumption/evaporation capacity

28

11

8

7

6

Remark: In additionto the specifications in the table, can be separately designed according tocustomer's specific material.

© 2017 Wenzhou chinz machinery co.,ltd All Rights Reserved